Secant Cardio IIe Spezifikationen

SYSTEM VERSION 2.5xx Installer’s guide

Advance configuration 7 Advance configuration The installer (advanced user) code gives access to a broader array of configuring data. For configuring

Advance configuration 8 Zones types CARDIO offers 16 programmable security inputs of 9 different types. • Delay: relevant to detectors a

Advance configuration 9 Delay Enter the maximum loop opening delay before an alarm is triggered. Values can run from 50 ms to 990 ms with

Advance configuration 10 Sun • Daylight saving (yes/no): to let the system automatically switch from Standard time to Daylight saving tim

Advance configuration 11 Monitoring • Client code: up to 2 client codes • Monitoring phone number: up to 2 different phone numbers. •

Advance configuration 12 System rep. Codes. • Restore: restore codes are given by the monitoring station for each type of alarm. For other

Advance configuration 13 • Temperature offset: because of the particular location of the touch panel, the temperature at the thermostat may vary from

Advance configuration 14 Central heating system Usually made up of a furnace and a two-wire thermostat (R and W). Installed in a central location, t

Advance configuration 15 HVAC System Made up of two separated items, a furnace and a cooler, controlled by a single thermostat with two set points. F

Advance configuration 16 HVAC setback Usually made up of two separate items: a heating system (furnace, baseboard heaters, etc.) and a cooling syste

LIMITED WARRANTY ... 1 INSTALLATION PROCEDURE ...

Advance configuration 17 Heating setback This is the type of control when the heating system is made of baseboard heaters only. Each zone (room) has

System restore 18 System restore There are two push buttons on the lower parts of the central controller printed circuit board (inside the metal box)

Troubleshooting 19 Troubleshooting This chapter addresses troubleshooting of the CARDIO system. Please note that even if CARDIO is connected to produ

Troubleshooting 20 Bus (SNet) protection To protect the central controller against noise, lightning and shorts that may occur on the bus. POLYSWITCH*

Troubleshooting 21 Telephone No tone from local (inside) telephone • Check if all cables are correctly connected: 1. CARDIO’s telephone cable conne

Troubleshooting 22 Type of telephone CARDIO can communicate with Touch-Tone telephones only. Central monitoring station When activating the account:

Troubleshooting 23 X-10 No control from screen We take for granted that all local tests described in the installation process have been achieved i.e.

Troubleshooting 24 Electronic transformers Very often, halogen lights are sold with a built-in electronic transformer. The electronic circuit of this

Troubleshooting 25 TEMPERATURE CONTROL (from CARDIO’s thermostat only) Nothing works Baseboard heaters 1. check breaker associated with baseboard he

Troubleshooting 26 Low temperature thermostat We strongly suggest that you install one thermostat used for low temperature detection (around 46 F or 8

Modules for incandescent light only...

Troubleshooting 27 Security Door/window contacts not changing status While you consecutively open and close a contact, the system do not change statu

Troubleshooting 28 General specifications of detectors that can be connected to CARDIO • voltage: between 12 and 14 Volt DC • maximal available curr

Troubleshooting 29 SECANT PERIPHERICAL PRODUCTS AND BUS. Touch screen(s) and key reader(s) None of the products is functioning 1. bad connection of

Troubleshooting 30 How to install the bus (refer to bus installation schematic) 1. wire the bus with the suggested cable; 2. leave a 10”loop out of

Troubleshooting 31 LED status There are two LEDs on the CARDIO central controller printed circuit board (inside the metal box). 1) The LED in the m

Schematics 32 Schematics INSTALLATION SCHEMATICS Touch panel installation A: Provided 4x #4-40 Hex machine screws B: Provided 4x #6 5/8 Wood screws

Schematics 33 Central controller installation D: To install the central controller use either the provided 4x #6 3/4 or the 4x #6 1”1/2 wood screws

Schematics 34 CONNECTIONS SCHEMATICS Peripheral connection schematic

Schematics 35 Key reader (EKRa) connection schematic

Schematics 36 Touch screen (TP2B) connection schematic NOTE: Use twisted pair of wires from CAT-5 or CAT-5e cable to wire the SNet Bus

Limited warranty 1 Limited warranty We appreciate your purchase of a Secant Home Automation Inc. product. We take pride of our products and they are

Schematics 37 TP2B Master/Slave configuration Follow these steps to select between master and slave mode. NOTE: The TP2B is set as "master&quo

Schematics 38 TP2B contrast adjustement Touch panel backside view (metal enclosure removed) Contrast adjustment screw. Turn counter clockwise to i

Schematics 39 Heating system connection schematic The following section describes the different connection schematics depending on the type of heatin

Schematics 40 2) Heat pump RH This type of temperature control system uses the relays labels « Heat », « Cool », « Fan ».and « Aux ». Heat This rela

Schematics 41 4) HVAC This type of temperature control system uses the relay labels « Heat », « Cool », « Fan ».and « Aux ». Heat This relay is clos

Schematics 42 5) HVAC setback This type of temperature control system uses the relay labels « Heat », « Cool » and « Fan ». Heat This relay is close

Schematics 43 6) Heating setback This type of temperature control system only uses the relay label « Heat ». In setback mode (economy) When the ambie

Schematics 44 Proverter HVAC controller connection schematic NOTE: Up to 4 Enerzone thermostat can be connected to the ProVerter. Therefore, wi

Schematics 45 Telephone connection schematic

Schematics 46 ADSL filter connection schematic

Limited warranty 2 THE SOFTWARE, HARDWARE, AND DOCUMENTATION IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, BUT NOT LIM

Schematics 47 Telephone menu

Schematics 48 PC to CARDIO connection schematic

Industry Canada Warnings 49 Industry Canada Warnings The Industry Canada Label identifies certified equipment. This certification means that the equ

1744, William street, suite 401 Montreal, Canada, H3J 1R4 Tel: (514) 935-3069 Fax: (514) 935-6655 email: [email protected] www.secant.ca SECAN

Installation procedure 3 Installation procedure The following is a suggested installation procedure for installing CARDIO and its peripheral items. W

Installation procedure 4 PRIOR TO THE INSTALLATION 9 Perform a complete analysis of the needs for each of the main functions (security, temperatur

Installation procedure 5 1- Security equipment installation 1) Select alarm detectors and sensors according to needs and location. 2) Check correct

Installation procedure 6 5- X-10 compatible module installation (if any) 1) Check loads to be controlled (type, power) and their respective specific